Here >> List > Blender
>>Blender
>Drive Principle
 |
When the input shaft rotates one circuit acentricly,due to the characteristics of cycloid wheel tooth profile curve and the restriction by needle teeth gear,which is why the cycloid wheel rotates with both the revolution and rotation.When the input shaft rotates one circle,the acentric sheath also rotates one circle,cycloid wheel will rotate in opposite direction to attain speed-down. |
| 1.Input Axes 2.Cycloid Wheel 3.Rotational Arm 4.Pin Teeth Crust |
>Features And Main Structure
- △High speed rate and effective
- △Compact configuration and small Voume
- △Light noise
- △Long life
- △Lgical design and convenient mend
 |
No. | Name | Material | No. | Name | Material |
| 1 | Output Axes | 45 | 10 | Fore Axes Sheath | GCr15 | |
| 2 | Fixed Ring | 45 | 11 | Pin Teeth | GCr15 | |
| 3 | Oil Seal | HT200 | 12 | Pin Teeth Crust | HT200 | |
| 4 | Base | HT200 | 13 | Cycloid Wheel | GCr15 | |
| 5 | Front Baffle Ring | A3 | 14 | Port Cover | HT200 | |
| 6 | Acentric Sheath | 45 | 15 | Back Baffle Ring | A3 | |
| 7 | Fore Axes | GCe15 | 16 | Fixed Ring | 45 | |
| 8 | Pin Teeth | GCr15 | 17 | Input Axes | 45 | |
| 9 | Interval Ring | HT200 |
>Models
Transmission Ratio And Input Power Table Of The Direct Single Motor-reducer
 |
B0 | B1 | B2 | B3 | B4 | B5 | B6 | B7 | B8 | |
| Input Rotate Rate 1500r/min |
Input Rotate Rate 1000/min |
|||||||||
| 9 | Output Rotate Rate166r/m | 0.75 | 2.2/1.5 | 3/2.2 | 7.5/5.5/4 | |||||
| 11 | Output Rotate Rate136r/m | 0.75 | 2.2/1.5 | 3/2.2 | 7.5/5.5/4 | 11 | 18.5/15 | |||
| 17 | Output Rotate Rate88r/m | 0.75 | 1.5/1.1 | 3/2.2 | 7.5/5.5/4 | 11 | 18.5/15 | 22 | 37 | |
| 23 | Output Rotate Rate65r/m | 0.55 | 1.5/1.1 | 3/2.2 | 5.5/4 | 11/7.5 | 18.5/15 | 22 | 37 | 55 |
| 29 | Output Rotate Rate51r/m | 0.55 | 1.1/0.75 | 2.2/1.5 | 5.5/4/3 | 7.5/5.5 | 15 | 18.5 | 37 | 55 |
| 35 | Output Rotate Rate42r/m | 0.37 | 1.1/1.75 | 1.5 | 4/3/2.2 | 7.5/5.5 | 15/11 | 15 | 30 | 45 |
| 43 | Output Rotate Rate34r/m | 0.37 | 0.75/0.55 | 1.5/1.1 | 4/3/2.2 | 5.5/4 | 11/7.5 | 11 | 22 | 40 |
| 59 | Output Rotate Rate25r/m | 0.25 | 0.75/0.55 | 1.1/0.75 | 2.2/1.5/1.1 | 4/3 | 7.5/5.5 | 7.5 | 18.5 | 30 |
| 71 | Output Rotate Rate21r/m | 0.18 | 0.55/0.37 | 0.75 | 2.2/1.5/1.1 | 3 | 5.5 | 7.5 | 15 | 22 |
| 87 | Output Rotate Rate17r/m | 0.12 | 1.5/1.1 | 3 | 5.5 | 5.5 | 11 | 22 | ||
>Order Notes
Please give us the power,rotate ratio,axes length,impeller dia.,material if you want.